Paparazzi UAS  v7.0_unstable
Paparazzi is a free software Unmanned Aircraft System.
gps_mediatek_diy module

Mediatek MT3329 GPS (UART)

Driver for Mediatek MT3329 GPS, DIYDrones V1.4/1.6 protocol

Example for airframe file

Add to your firmware section: This example contains all possible configuration options, not all of them are mandatory!

<module name="gps_mediatek_diy">
b'<configure name="MTK_GPS_PORT" value="UARTx" />\n '
b'<configure name="MTK_GPS_BAUD" value="B38400" />\n '
</module>

Module configuration options

Configure Options

  • name: MTK_GPS_PORT value: UARTx
    Description: UART where the GPS is connected to (UART1, UART2, etc
  • name: MTK_GPS_BAUD value: B38400
    Description: UART baud rate

Module functions

Init Functions

These initialization functions are called once on startup.

Event Functions

These event functions are called in each cycle of the module event loop.

Periodic Functions

These functions are called periodically at the specified frequency from the module periodic loop.

Files

Header Files

The following headers are automatically included in modules.h

Source Files

Raw gps_mediatek_diy.xml file:

<!DOCTYPE module SYSTEM "module.dtd">
<module name="gps_mediatek_diy" dir="gps" task="sensors">
<doc>
<description>
Mediatek MT3329 GPS (UART)
Driver for Mediatek MT3329 GPS, DIYDrones V1.4/1.6 protocol
</description>
<configure name="MTK_GPS_PORT" value="UARTx" description="UART where the GPS is connected to (UART1, UART2, etc"/>
<configure name="MTK_GPS_BAUD" value="B38400" description="UART baud rate"/>
</doc>
<dep>
<depends>uart,gps</depends>
<provides>gps</provides>
</dep>
<header>
<file name="gps.h"/>
</header>
<init fun="gps_mtk_init()"/>
<periodic fun="gps_mtk_periodic_check()" freq="1." autorun="TRUE"/>
<event fun="gps_mtk_event()"/>
<makefile target="ap|fbw">
<configure name="MTK_GPS_PORT" default="$(GPS_PORT)" case="upper|lower"/>
<configure name="MTK_GPS_BAUD" default="$(GPS_BAUD)"/>
<file name="gps_mtk.c"/>
<define name="USE_$(MTK_GPS_PORT_UPPER)"/>
<define name="MTK_GPS_LINK" value="$(MTK_GPS_PORT_LOWER)"/>
<define name="$(MTK_GPS_PORT_UPPER)_BAUD" value="$(MTK_GPS_BAUD)"/>
<raw>
ifdef SECONDARY_GPS
ifneq (,$(findstring $(SECONDARY_GPS), mtk mediatek))
# this is the secondary GPS
$(TARGET).CFLAGS += -DGPS_SECONDARY_TYPE_H=\"modules/gps/gps_mtk.h\"
$(TARGET).CFLAGS += -DSECONDARY_GPS=GPS_MTK
else
$(TARGET).CFLAGS += -DGPS_TYPE_H=\"modules/gps/gps_mtk.h\"
$(TARGET).CFLAGS += -DPRIMARY_GPS=GPS_MTK
endif
else
# plain old single GPS usage
$(TARGET).CFLAGS += -DGPS_TYPE_H=\"modules/gps/gps_mtk.h\"
endif
</raw>
<test>
<define name="PRIMARY_GPS" value="GPS_MTK"/>
<define name="MTK_GPS_PORT" value="uart2"/>
<define name="MTK_GPS_BAUD" value="115200"/>
<define name="USE_UART2"/>
<define name="MTK_GPS_LINK" value="uart2"/>
</test>
</makefile>
<makefile target="fbw">
<define name="USE_GPS"/>
</makefile>
</module>