Decoder for standardized messages from the JEVOIS smart camera (http://jevois.org)

Data are extracted from a serial link and produce a JEVOIS_MSG ABI message

Example for airframe file

Add to your firmware section: This example contains all possible configuration options, not all of them are mandatory!

 <module name="jevois">
   <define name="JEVOIS_SEND_MSG" value="FALSE|TRUE" />
   <configure name="JEVOIS_UART" value="UARTX" />
   <configure name="JEVOIS_BAUD" value="B115200" />
 </module>

Module configuration options

Configure Options

name: JEVOIS_UART value: UARTX
Description: UART on which Jevois camera is connected
name: JEVOIS_BAUD value: B115200
Description: UART Baudrate, default to 115200

Define Options

name: JEVOIS_SEND_MSG value: FALSE|TRUE
Description: Send synchronized jevois message over telemetry link, use periodic report function otherwise

Module functions

Init Functions

These initialization functions are called once on startup.

jevois_init()

Event Functions

These event functions are called in each cycle of the module event loop.

jevois_event()

Periodic Functions

These functions are called periodically at the specified frequency from the module periodic loop.

jevois_report()
- Frequency in Hz: 5
- Autorun: FALSE
  Periodic function is started by user command.
jevois_send_state()
- Frequency in Hz: 4
- Autorun: TRUE
  Periodic function automatically starts after init.

Files

Header Files

The following headers are automatically included in modules.h

jevois.h

Source Files

modules/sensors/cameras/jevois.c

Raw jevois.xml file:

<!DOCTYPE module SYSTEM "module.dtd">
<module name="jevois" dir="sensors/cameras">
  <doc>
    <description>
      Decoder for standardized messages from the JEVOIS smart camera (http://jevois.org)
      Data are extracted from a serial link and produce a JEVOIS_MSG ABI message
    </description>
    <configure name="JEVOIS_UART" value="UARTX" description="UART on which Jevois camera is connected"/>
    <configure name="JEVOIS_BAUD" value="B115200" description="UART Baudrate, default to 115200"/>
    <define name="JEVOIS_SEND_MSG" value="FALSE|TRUE" description="Send synchronized jevois message over telemetry link, use periodic report function otherwise"/>
  </doc>
  <settings>
    <dl_settings>
      <dl_settings NAME="JeVois">
        <dl_setting MAX="20" MIN="0" STEP="1" VAR="jevois_mapping_setting" shortname="mapping" module="modules/sensors/cameras/jevois" handler="setmapping"/>
        <dl_setting MAX="1" MIN="0" STEP="1" VAR="jevois_stream_setting" shortname="stream" module="modules/sensors/cameras/jevois" handler="stream" values="FALSE|TRUE"/>
      </dl_settings>
    </dl_settings>
  </settings>
  <header>
    <file name="jevois.h"/>
  </header>
  <init fun="jevois_init()"/>
  <periodic fun="jevois_report()" freq="5" autorun="FALSE"/>
  <periodic fun="jevois_send_state()" freq="4" autorun="TRUE"/>
  <event fun="jevois_event()"/>
  <makefile>
    <configure name="JEVOIS_UART" case="upper|lower"/>
    <configure name="JEVOIS_BAUD" default="B115200"/>
    <file name="jevois.c"/>
    <define name="USE_$(JEVOIS_UART_UPPER)"/>
    <define name="JEVOIS_DEV" value="$(JEVOIS_UART_LOWER)"/>
    <define name="$(JEVOIS_UART_UPPER)_BAUD" value="$(JEVOIS_BAUD)"/>
  </makefile>
</module>