Direct SPI SD Logger that saves pprzlog messages to SD Card.

This module logs data directly to an SD Card which is connected on a SPI port. For now, it is only possible to use a radio switch to start and stop logging.

The values to be logged are defined in the telemetry config file. An example is available in rotorcraft_with_logger.xml. The logmessage is defined as the default message in the process "Logger".

A LOGGER_LED can be enabled which indicates if the logger is writing or reading data.

Downloading of the data occurs over an UART datalink. There is no check to verify that all data is transfered, so it is recommended to use an FTDI cable to the UART port.

Do not use start/stop functionality of the module, the module is not intended to be used like this.

Example for airframe file

Add to your firmware section: This example contains all possible configuration options, not all of them are mandatory!

 <module name="logger_sd_spi_direct">
   <configure name="SDLOGGER_DIRECT_SPI" value="SPI1|SPI2|SPI3|SPI4|SPI5|SPI6" />
   <configure name="SDLOGGER_DIRECT_SPI_SLAVE" value="SPI_SLAVE1|SPI_SLAVE2|SPI_SLAVE3|SPI_SLAVE4|SPI_SLAVE5|SPI_SLAVE6" />
   <configure name="SDLOGGER_DIRECT_CONTROL_SWITCH" value="RADIO_AUX2" />
   <configure name="LOGGER_LED" value="none" />
 </module>

Module configuration options

Configure Options

name: SDLOGGER_DIRECT_SPI value: SPI1|SPI2|SPI3|SPI4|SPI5|SPI6
Description: Port to which the SD Card is connected.
name: SDLOGGER_DIRECT_SPI_SLAVE value: SPI_SLAVE1|SPI_SLAVE2|SPI_SLAVE3|SPI_SLAVE4|SPI_SLAVE5|SPI_SLAVE6
Description: Port to which the SD Card is connected.
name: SDLOGGER_DIRECT_CONTROL_SWITCH value: RADIO_AUX2
name: LOGGER_LED value: none

Module functions

Init Functions

These initialization functions are called once on startup.

sdlogger_spi_direct_init()

Periodic Functions

These functions are called periodically at the specified frequency from the module periodic loop.

sdlogger_spi_direct_periodic()
- Frequency in Hz: 512
- Autorun: TRUE
  Periodic function automatically starts after init.
- Start function: sdlogger_spi_direct_start()
  Executed before the periodic function starts.
- Stop function: sdlogger_spi_direct_stop()
  Executed after the periodic function stops.

Datalink Functions

Whenever the specified datalink message is received, the corresponing handler function is called.

on message SETTING call sdlogger_spi_direct_command()

Files

Header Files

The following headers are automatically included in modules.h

sdlogger_spi_direct.h

Source Files

Raw logger_sd_spi_direct.xml file:

<!DOCTYPE module SYSTEM "module.dtd">
<module name="logger_sd_spi_direct" dir="loggers">
  <doc>
    <description>
Direct SPI SD Logger that saves pprzlog messages to SD Card.
This module logs data directly to an SD Card which is connected on a SPI port. For now, it is only possible to use a radio switch to start and stop logging.
The values to be logged are defined in the telemetry config file. An example is available in rotorcraft_with_logger.xml. The logmessage is defined as the default message in the process "Logger".
A LOGGER_LED can be enabled which indicates if the logger is writing or reading data.
Downloading of the data occurs over an UART datalink. There is no check to verify that all data is transfered, so it is recommended to use an FTDI cable to the UART port.
Do not use start/stop functionality of the module, the module is not intended to be used like this.
</description>
    <configure name="SDLOGGER_DIRECT_SPI" value="SPI1|SPI2|SPI3|SPI4|SPI5|SPI6" description="Port to which the SD Card is connected."/>
    <configure name="SDLOGGER_DIRECT_SPI_SLAVE" value="SPI_SLAVE1|SPI_SLAVE2|SPI_SLAVE3|SPI_SLAVE4|SPI_SLAVE5|SPI_SLAVE6" description="Port to which the SD Card is connected."/>
    <configure name="SDLOGGER_DIRECT_CONTROL_SWITCH" value="RADIO_AUX2"/>
    <configure name="LOGGER_LED" value="none"/>
  </doc>
  <settings>
    <dl_settings NAME="sdlogger">
      <dl_settings NAME="SD Logger">
        <dl_setting module="loggers/sdlogger_spi_direct" var="sdlogger_spi.status" min="0" max="20" step="1"/>
        <dl_setting module="loggers/sdlogger_spi_direct" var="sdcard1.status" min="0" max="40" step="1"/>
        <dl_setting module="loggers/sdlogger_spi_direct" var="sdcard1.error_status" min="0" max="15" step="1"/>
        <dl_setting module="loggers/sdlogger_spi_direct" var="sdlogger_spi.command" min="1" max="42" step="1" />
        <dl_setting module="loggers/sdlogger_spi_direct" var="sdlogger_spi.do_log" min="0" max="1" step="1" values="Off|On"/>
      </dl_settings>
    </dl_settings>
  </settings>
  <header>
    <file name="sdlogger_spi_direct.h"/>
  </header>
  <init fun="sdlogger_spi_direct_init()"/>
  <periodic fun="sdlogger_spi_direct_periodic()" freq="512" start="sdlogger_spi_direct_start()" stop="sdlogger_spi_direct_stop()" autorun="TRUE"/>
  <datalink message="SETTING" fun="sdlogger_spi_direct_command()"/>
  <makefile target="ap">
    <configure name="SDLOGGER_DIRECT_SPI" default="spi2" case="upper|lower"/>
    <configure name="SDLOGGER_DIRECT_SPI_SLAVE" default="spi_slave2" case="upper|lower"/>
    <configure name="LOGGER_LED" default="none"/>
    <define name="LOGGER_LED" value="$(LOGGER_LED)" cond="ifneq ($(LOGGER_LED),none)"/>
    <raw>
        include $(CFG_SHARED)/sdlog.makefile
        include $(CFG_SHARED)/spi_master.makefile
    </raw>
    <file name="sdcard_spi.c" dir="peripherals"/>
    <file name="sdlogger_spi_direct.c"/>
    <define name="USE_$(SDLOGGER_DIRECT_SPI_UPPER)" value="1" />
    <define name="SDLOGGER_SPI_LINK_DEVICE" value="$(SDLOGGER_DIRECT_SPI_LOWER)" />
    <define name="USE_$(SDLOGGER_DIRECT_SPI_SLAVE_UPPER)" value="1" />
    <define name="SDLOGGER_SPI_LINK_SLAVE_NUMBER" value="$(SDLOGGER_DIRECT_SPI_SLAVE_UPPER)" />
  </makefile>
</module>