Battery checker module

When the battery voltage goes below the BAT_LOW level, this will toggle a GPIO/LED. If the battery voltage is lower than BAT_CRITICAL level, the LED/GPIO stays ON. The output signal can be connected to an actaul LED or a buzzer to indicated the end of battery to the user.

When a LED is used, define the LED number in your airframe with BAT_CHECKER_LED. When a GPIO is used, define the GPIO port and pin in your airframe with BAT_CHECKER_GPIO. You should at least use one of these two options.

Example for airframe file

Add to your firmware section: This example contains all possible configuration options, not all of them are mandatory!

 <module name="bat_checker">
   <define name="BAT_CHECKER_DELAY" value="delay" />
   <define name="BAT_CHECKER_LED" value="X" />
   <define name="BAT_CHECKER_GPIO" value="GPIOX,GPIOY" />
   <define name="BAT_CHECKER_GPIO_ON" value="gpio_set" />
   <define name="BAT_CHECKER_GPIO_OFF" value="gpio_clear" />
 </module>

Module configuration options

Define Options

name: BAT_CHECKER_DELAY value: delay
Description: number of seconds the battery voltage has to below LOW_BAT_LEVEL before warning signal is activated
name: BAT_CHECKER_LED value: X
Description: led number to use for the warning signal
name: BAT_CHECKER_GPIO value: GPIOX,GPIOY
Description: alternatively, a GPIO can be set instead of a LED (ex: GPIOA,GPIO5)
name: BAT_CHECKER_GPIO_ON value: gpio_set
Description: tells if output signal is ON when GPIO is high or low
name: BAT_CHECKER_GPIO_OFF value: gpio_clear
Description: tells if output signal is OFF when GPIO is high or low

Module functions

Init Functions

These initialization functions are called once on startup.

init_bat_checker()

Periodic Functions

These functions are called periodically at the specified frequency from the module periodic loop.

bat_checker_periodic()
- Frequency in Hz: 2
- Autorun: TRUE
  Periodic function automatically starts after init.

Files

Header Files

The following headers are automatically included in modules.h

bat_checker.h

Source Files

modules/energy/bat_checker.c

Raw bat_checker.xml file:

<!DOCTYPE module SYSTEM "module.dtd">
<module name="bat_checker" dir="energy">
  <doc>
    <description>
      Battery checker module
      When the battery voltage goes below the BAT_LOW level, this will toggle a GPIO/LED.
      If the battery voltage is lower than BAT_CRITICAL level, the LED/GPIO stays ON.
      The output signal can be connected to an actaul LED or a buzzer to indicated the end of battery to the user.
      When a LED is used, define the LED number in your airframe with BAT_CHECKER_LED.
      When a GPIO is used, define the GPIO port and pin in your airframe with BAT_CHECKER_GPIO.
      You should at least use one of these two options.
    </description>
    <define name="BAT_CHECKER_DELAY" value="delay" description="number of seconds the battery voltage has to below LOW_BAT_LEVEL before warning signal is activated"/>
    <define name="BAT_CHECKER_LED" value="X" description="led number to use for the warning signal"/>
    <define name="BAT_CHECKER_GPIO" value="GPIOX,GPIOY" description="alternatively, a GPIO can be set instead of a LED (ex: GPIOA,GPIO5)"/>
    <define name="BAT_CHECKER_GPIO_ON" value="gpio_set" description="tells if output signal is ON when GPIO is high or low"/>
    <define name="BAT_CHECKER_GPIO_OFF" value="gpio_clear" description="tells if output signal is OFF when GPIO is high or low"/>
  </doc>
  <header>
    <file name="bat_checker.h"/>
  </header>
  <init fun="init_bat_checker()"/>
  <periodic fun="bat_checker_periodic()" freq="2" autorun="TRUE"/>
  <makefile target="ap">
    <file name="bat_checker.c"/>
  </makefile>
</module>