ins_vectornav module

Vectornav INS Driver.

No detailed description...

Example for airframe file

Add to your firmware section: This example contains all possible configuration options, not all of them are mandatory!

<module name="ins_vectornav">
  <configure name="VN_PORT" value="uart3" />
  <configure name="VN_BAUD" value="B921600" />
</module>

Module configuration options

Configure Options

• name: VN_PORT value: uart3
  Description: UART to use
• name: VN_BAUD value: B921600
  Description: UART baudrate

Auto-loaded modules

The following modules are automatically loaded (just as if you had added them in the airframe file)

• gps module
• ins_sim module
• ins_nps module

Module functions

Init Functions

These initialization functions are called once on startup.

• ins_vectornav_init()

Event Functions

These event functions are called in each cycle of the module event loop.

• ins_vectornav_event()

Periodic Functions

These functions are called periodically at the specified frequency from the module periodic loop.

• ins_vectornav_monitor()
  • Frequency in Hz: 1.0
  • Autorun: TRUE
    Periodic function automatically starts after init.

Files

Header Files

The following headers are automatically included in modules.h

• ins.h

Source Files

• peripherals/vn200_serial.c
• subsystems/ins.c
• subsystems/ins/ins_vectornav.c
• subsystems/ins/ins_vectornav_wrapper.c
• subsystems/gps.c

Raw ins_vectornav.xml file:

<!DOCTYPE module SYSTEM "module.dtd">

<module name="ins_vectornav" dir="ins">
  <doc>
    <description>
      Vectornav INS Driver.
    </description>
    <configure name="VN_PORT" value="uart3" description="UART to use"/>
    <configure name="VN_BAUD" value="B921600" description="UART baudrate"/>
  </doc>
  <autoload name="gps"/>
  <autoload name="ins_sim"/>
  <autoload name="ins_nps"/>
  <header>
    <file name="ins.h" dir="subsystems"/>
  </header>
  <init fun="ins_vectornav_init()"/>
  <periodic fun="ins_vectornav_monitor()" freq="1.0" autorun="TRUE"/>
  <event fun="ins_vectornav_event()"/>
  <makefile target="ap">
    <configure name="VN_PORT" default="uart3" case="upper|lower"/>
    <configure name="VN_BAUD" default="B921600"/>
    <define name="USE_$(VN_PORT_UPPER)"/>
    <define name="VN_PORT" value="$(VN_PORT_LOWER)"/>
    <define name="$(VN_PORT_UPPER)_BAUD" value="$(VN_BAUD)"/>

    <define name="GPS_NB_CHANNELS" value="1" description="define a single GPS channel to show pacc on GCS GPS page"/>

    <file name="vn200_serial.c" dir="peripherals"/>

    <file name="ins.c" dir="subsystems"/>
    <file name="ins_vectornav.c" dir="subsystems/ins"/>
    <file name="ins_vectornav_wrapper.c" dir="subsystems/ins"/>
    <define name="INS_TYPE_H" value="subsystems/ins/ins_vectornav_wrapper.h" type="string"/>

    <file name="gps.c" dir="subsystems"/>
    <define name="USE_GPS"/>
    <raw>
      ifdef SECONDARY_GPS
      ifneq (,$(findstring $(SECONDARY_GPS), vectornav))
      # this is the secondary GPS
      ap.CFLAGS += -DGPS_SECONDARY_TYPE_H=\"subsystems/ins/ins_vectornav_wrapper.h\"
      ap.CFLAGS += -DSECONDARY_GPS=GPS_VECTORNAV
      else
      ap.CFLAGS += -DGPS_TYPE_H=\"subsystems/ins/ins_vectornav_wrapper.h\"
      ap.CFLAGS += -DPRIMARY_GPS=GPS_VECTORNAV
      endif
      else
      # plain old single GPS usage
      ap.CFLAGS += -DGPS_TYPE_H=\"subsystems/gps/gps_ubx.h\"
      endif
    </raw>
  </makefile>
</module>