board_matek_f765_wing module

Autoload several onboard sensors and modules

for the Matek F765 Wing board with proper configuration. IMU ICM20602 (auto-detected from MPU6000 driver) Baro (BMP280) OSD Normal back of the board is on the battery/ESC wires Normal up of the board is on MCU side.

Example for airframe file

Add to your firmware section: This example contains all possible configuration options, not all of them are mandatory!

<module name="board_matek_f765_wing">
  b'<configure name="BOARD_MATEK_ROTATED" value="FALSE|TRUE" />\n  '
</module>

Module configuration options

Configure Options

• name: BOARD_MATEK_ROTATED value: FALSE|TRUE
  Description: if TRUE, the board is not using is default orientation and axis can be redefined by hand

Files

Raw board_matek_f765_wing.xml file:

<!DOCTYPE module SYSTEM "module.dtd">
 
<module name="board_matek_f765_wing" dir="boards">
  <doc>
    <description>
      Autoload several onboard sensors and modules
      for the Matek F765 Wing board with proper configuration.
      IMU ICM20602 (auto-detected from MPU6000 driver)
      Baro (BMP280)
      OSD
      Normal back of the board is on the battery/ESC wires
      Normal up of the board is on MCU side.
    </description>
    <configure name="BOARD_MATEK_ROTATED" value="FALSE|TRUE" description="if TRUE, the board is not using is default orientation and axis can be redefined by hand"/>
  </doc>
  <dep>
    <depends>spi_master,osd_max7456,baro_bmp280_i2c,current_sensor,imu_mpu6000</depends>
  </dep>
 
  <makefile target="!sim|nps|fbw">
    <!-- IMU CONFIGURATION -->
    <configure name="IMU_MPU_SPI_DEV" value="spi3" case="upper|lower"/>
    <configure name="IMU_MPU_SPI_SLAVE_IDX" value="SPI_SLAVE4"/>
    <define name="IMU_MPU_GYRO_RANGE" value="MPU60X0_GYRO_RANGE_1000"/>
    <define name="IMU_MPU_ACCEL_RANGE" value="MPU60X0_ACCEL_RANGE_8G"/>
    <define name="IMU_MPU_CHAN_X" value="1" cond="ifeq (,$(findstring $(BOARD_MATEK_ROTATED),1 TRUE))"/>
    <define name="IMU_MPU_CHAN_Y" value="0" cond="ifeq (,$(findstring $(BOARD_MATEK_ROTATED),1 TRUE))"/>
    <define name="IMU_MPU_X_SIGN" value="-1" cond="ifeq (,$(findstring $(BOARD_MATEK_ROTATED),1 TRUE))"/>
    <!-- BAROMETER BMP280 CONFIGURATION -->
    <configure name="BMP280_I2C_DEV" value="i2c2"/>
    <!-- OSD CONFIGURATION -->
    <configure name="MAX7456_SPI_DEV" value="spi2"/>
    <configure name="MAX7456_SLAVE_IDX" value="SPI_SLAVE5"/>
    <define name="USE_MATEK_TYPE_OSD_CHIP" value="true" />
    <define name="USE_PAL_FOR_OSD_VIDEO" value="true" />
    <define name="BARO_ALTITUDE_VAR" value="baro_alt" /> <!-- if non defined the default var is ''baro_alt'' -->
    <!-- CURRENT SENSOR -->
    <configure name="ADC_CURRENT_SENSOR" value="ADC_4"/>
  </makefile>
</module>